ASTM-A635 2008

$40.63

A635/A635M-08 Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General Requirements for

Published By	Publication Date	Number of Pages
ASTM	2008	10

Guaranteed Safe Checkout

Categories: 77.140.50 - Flat steel products and semi-products, ASTM

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Description

ASTM A635/A635M-08

Historical Standard: Standard Specification for Steel, Sheet and Strip, Heavy-Thickness Coils, Hot-Rolled, Alloy, Carbon, Structural, High-Strength Low-Alloy, and High-Strength Low-Alloy with Improved Formability, General Requirements for

ASTM A635/A635M

Scope

1.1 This specification covers the general requirements for hot-rolled, heavy-thickness sheet and strip in coils.

1.2 It applies to Specification A 1018/A 1018M.

1.3 This material is available only in coils described as follows:

Note 1—The changes in width limits with the publication of A 635/A 635M – 06a result in a change in tensile testing direction for material from 0.180 in. [4.5 mm] to 0.230 in. exclusive [6.0 mm exclusive] over 48 in. [1200 mm] wide as that material is now covered by Specification A 568/A 568M – 06a. The purchaser is advised to discuss this change with the supplier.

1.4 In case of any conflict in requirements, the requirements of the individual material specification shall prevail over those of this general specification.

1.5 Annex A1 lists permissible variations in dimensions and mass (see Note 2) in SI [metric] units. The values listed are not exact conversions of the values listed in the inch-pound tables, but instead are rounded or rationalized values. Conformance to Annex A1 is mandatory when the “M” specification is used.

Note 2—The term weight is used when inch-pound units are the standard. However, under SI, the preferred term is mass.

1.6 The values stated in either SI units or inch-pound units are to be regarded separately as standard. The values stated in each system may not be exact equivalents; therefore, each system shall be used independently of the other. Combining values from the two systems may result in non-conformance with the standard.

1.7 This specification and the applicable material specifications are expressed in both inch-pound units and SI units. However, unless the order specifies the applicable “M” specification designation (SI units), the material shall be furnished to inch-pound units.

Keywords

carbon ; commercial; drawing; heavy thickness coils; high-strength low-alloy; high-strength low-alloy with improved formability; sheet steel; strip steel; Carbon steel sheet/strip–specifications; Commercial steel (CS) sheet/strip–specifications; General delivery requirements–steel; Heavy-thickness steel coils–specifications; High-strength structural steel–specifications; Hot-rolled steel sheet/strip–specifications; Structural steel (SS) sheet/strip–specifications

ICS Code

ICS Number Code 77.140.50 (Flat steel products and semi-products)

DOI: 10.1520/A0635_A0635M-08

PDF Catalog

PDF Pages	PDF Title
1	Scope Referenced Documents
2	Terminology Index of Tables, Dimensions, and Allowances Materials and Manufacture Chemical Composition
3	Mechanical Properties Dimensions and Tolerances Workmanship, Finish, and Appearance TABLE 1 TABLE 2
4	Retests and Disposition of Non-Conforming Material TABLE 3 TABLE 4 TABLE 5 TABLE 6
5	TABLE 7 TABLE 8 TABLE 9 TABLE 10 TABLE 11
6	Inspection Rejection and Rehearing Test Reports and Certification Product Marking Packaging and Package Marking Keywords
7	A1. PERMISSIBLE VARIATIONS IN DIMENSIONS AND MASS IN SI UNITS A1.1 TABLE A1.1
8	TABLE A1.2 TABLE A1.3 TABLE A1.4 TABLE A1.5
9	TABLE A1.6 TABLE A1.7
10	TABLE A1.8 TABLE A1.9 TABLE A1.10