BS EN 14354:2017 – TC:2020 Edition
$258.95
Tracked Changes. Wood-based panels. Wood veneer floor coverings
| Published By | Publication Date | Number of Pages |
| BSI | 2020 | 134 |
This European Standard defines terms and specifies requirements and test methods for wood veneer floor coverings with multilayer built up for internal use. It gives guidance for the evaluation of conformity of the products to the requirements of this standard. This European Standard is not applicable to multilayer parquet elements with a minimum top layer thickness of 2,5 mm. For these products EN 13489 applies.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 82 | National foreword |
| 88 | 1 Scope 2 Normative references |
| 89 | 3 Terms and definitions |
| 90 | 4 Requirements 4.1 General 4.2 General requirements |
| 91 | 5 Classification requirements 5.1 General |
| 92 | 5.2 Classification requirements for elements with lacquered surfaces 6 Marking and packaging 6.1 Marking |
| 93 | 6.2 Packaging 7 Test report |
| 94 | Annex A (normative)Determination of thickness, length, width, squareness, deviation from edge straightness and cup A.1 General A.2 Sampling A.3 Conditioning A.4 Test equipment |
| 95 | A.5 Procedure A.5.1 Determination of thickness t |
| 96 | A.5.2 Determination of length l A.5.3 Determination of width w and dimensions of squared elements |
| 97 | A.5.4 Determination of deviation from squareness q A.5.5 Determination of deviation of edge straightness s |
| 98 | A.5.6 Determination of cup fw A.6 Calculation and expression of results A.6.1 Thickness t A.6.2 Width w A.6.3 Length l A.6.4 Deviation from squareness q A.6.5 Deviation from edge straightness s |
| 99 | A.6.6 Cup fw A.7 Test report |
| 100 | Annex B (normative)Determination of opening and lipping between elements B.1 General B.2 Sampling B.3 Conditioning B.4 Test equipment B.5 Procedure B.5.1 Assembling |
| 101 | B.5.2 Measuring of lipping B.5.3 Measuring of openings B.5.4 Calculation and expression of results B.6 Test report |
| 102 | Annex C (normative)Determination of the elasticity of lacquer C.1 General C.2 Sampling C.3 Apparatus C.4 Procedure C.5 Calculation and expression of results C.6 Evaluation of results, elasticity classification |
| 103 | Annex D (normative)Determination of the wear resistance using the falling sand method D.1 General D.2 Sampling D.3 Conditioning |
| 104 | D.4 Apparatus D.4.1 Testing machine D.4.1.1 General D.4.1.2 Test specimen holder D.4.1.3 Holding and lifting device D.4.1.4 Revolution-counter D.4.2 Grit feeder and accessories D.4.2.1 General D.4.2.2 Vacuum cleaning device |
| 107 | D.4.2.3 Abrading material D.4.2.4 Leather abrading wheels |
| 108 | D.4.2.5 Stopwatch D.4.2.6 Grit collection container D.4.2.7 Calibration plates D.4.2.8 Transparent template to evaluate the wear of the abraded area |
| 109 | D.4.3 Additional material or equipment D.4.3.1 Weighing equipment D.4.3.2 Conditioning chamber D.4.3.3 Contrast marking solutions D.5 Procedure D.5.1 General D.5.2 Maintenance of the abrading wheels D.5.3 Operation of the abrader |
| 110 | D.5.4 Calibration D.5.4.1 Rate of grit flow D.5.4.2 Abrading capacity |
| 111 | D.5.5 Abrasion of test specimen D.5.5.1 Conditioning D.5.5.2 Printed surfaces D.5.5.3 Non-printed surfaces |
| 112 | D.6 Expression of results D.7 Test report |
| 113 | Annex E (normative)Determination of abrasion resistance using the sand paper method E.1 General E.2 Sampling E.3 Conditioning |
| 114 | E.4 Apparatus E.4.1 Testing machine E.4.1.1 General E.4.1.2 Test specimen holder E.4.1.3 Holding and lifting device E.4.1.4 Rubber covered abrasive wheels E.4.1.5 Abrasive paper strips |
| 115 | E.4.1.6 Calibration plates E.4.1.7 Suction device E.4.1.8 Revolution-counter |
| 117 | E.4.2 Additional material or equipment E.4.2.1 Weighing equipment E.4.2.2 Conditioning chamber E.4.2.3 Transparent template to evaluate the wear of the abraded area E.4.2.4 Contrast marking solutions E.5 Procedure E.5.1 General |
| 118 | E.5.2 Preparation of test specimens and abrasive papers E.5.3 Preparation of abrasive wheels E.5.4 Determination of the abrasion rate of abrasive paper E.5.5 Abrasion of test specimen E.5.5.1 General E.5.5.2 Printed surfaces |
| 120 | E.5.5.3 Non-printed surfaces E.5.6 Expression of results E.5.7 Test report |
| 121 | Annex F (normative)Determination of the adhesion of the lacquer — Cross cut test F.1 General F.2 Test equipment F.2.1 Cutting tool |
| 123 | F.2.2 Spacing guide F.2.3 Soft brush F.2.4 Transparent pressure-sensitive adhesive tape |
| 124 | F.3 Sampling F.4 Test procedure F.4.1 General F.4.1.1 Conditioning of the elements F.4.1.2 Test conditions and number of tests F.4.1.3 Number of cuts F.4.1.4 Spacing of cuts F.4.2 Cutting and removing the lacquer |
| 125 | F.5 Expression of the results |
| 126 | F.6 Test report |
| 127 | Annex G (normative)Complementary properties |
| 128 | Annex H (informative)Guide for evaluation of conformity of product quality H.1 General H.2 Terms and definitions |
| 129 | H.3 Rules for evaluation of conformity H.3.1 Batch H.3.2 Sampling H.3.3 Evaluation of conformity H.3.3.1 General H.3.3.2 Wood species H.3.3.3 Top layer quality H.3.3.4 Geometrical characteristics H.3.3.5 Moisture content H.3.3.6 Acceptance and rejection |
| 130 | H.4 Sampling report |
Related products
-
BS EN 14354:2017
Wood-based panels. Wood veneer floor coverings Published By Publication Date Number of Pages BSI 2017…
