BS EN 14891:2017 – TC:2020 Edition
$217.84
Tracked Changes. Liquid applied water impermeable products for use beneath ceramic tiling bonded with adhesives. Requirements, test methods, assessment and verification of constancy of performance, classification and marking
| Published By | Publication Date | Number of Pages |
| BSI | 2020 | 87 |
This European Standard applies to all liquid-applied water impermeable products, based on polymer modified cementitious mortars, dispersions and reaction resin coatings, used beneath ceramic tiling, for external tile installations on walls and floors and in swimming pools. This European Standard gives the terminology concerning the products and specifies the test methods and the values of performance requirements for liquid-applied water impermeable products associated with tile adhesives. This European Standard specifies the evaluation of conformity and the classification and designation of liquid-applied water impermeable products beneath ceramic tiling. This European Standard does not contain recommendations for the design and installation of ceramic tiles and grouts in combination with water impermeable products. NOTE 1 Liquid-applied water impermeable products may also be used beneath other types of tiles (natural and agglomerated stones, etc.), where they do not adversely affect these materials. NOTE 2 The user of this European Standard should be familiar with normal laboratory practice. This European Standard does not purport to address all the safety problems associated with its use. It is the responsibility of the user to establish appropriate health and safety practices and to ensure compliance with any European and national regulatory conditions.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 1 | compares BS EN 14891:2017 |
| 2 | TRACKED CHANGES Text example 1 — indicates added text (in green) |
| 54 | 1 Scope 2 Normative references |
| 55 | 3 Terms and definitions |
| 56 | 4 Product characteristics 4.1 General 4.2 Release of dangerous substances |
| 57 | 5 Testing, assessment and sampling methods 6 Assessment and verification of constancy of performance (AVCP) 6.1 General 6.2 Type testing 6.2.1 General |
| 58 | 6.2.2 Test samples, testing and compliance criteria 6.2.3 Test reports 6.2.4 Shared other party results |
| 59 | 6.3 Factory Production Control (FPC) 6.3.1 General 6.3.2 Requirements 6.3.2.1 General |
| 60 | 6.3.2.2 Equipment |
| 61 | 6.3.2.3 Raw materials and components 6.3.2.4 Traceability and marking 6.3.2.5 Controls during manufacturing process 6.3.2.6 Product testing and evaluation |
| 62 | 6.3.2.7 Non-complying products 6.3.2.8 Corrective action 6.3.2.9 Handling, storage and packaging 6.3.3 Product specific requirements |
| 63 | 6.3.4 Procedure for modifications 6.3.5 One-off products, pre-production products (e.g. prototypes) and products produced in very low quantity |
| 64 | 7 Classification and designation |
| 65 | 8 Marking and labelling |
| 67 | Annex A (normative)Testing, assessment and sampling methods A.1 Sampling A.2 Test conditions A.3 Test materials A.3.1 General A.3.2 Ceramic tiles A.3.3 Test substrate A.3.3.1 Concrete slab A.3.3.2 Other substrates (optional) |
| 68 | A.3.4 Ceramic tile adhesive A.3.5 Sodium hypochlorite A.4 Apparatus A.4.1 Weight (Mass) A.4.2 Pull head plates A.4.3 Machine for pull testing A.4.4 Air-circulating oven A.4.5 Mould |
| 70 | A.4.6 Jig |
| 71 | A.4.7 Equipment for permeability test |
| 72 | A.4.8 Machine for tensile testing A.5 Mixing of liquid-applied water impermeable products A.6 Tensile adhesion tests A.6.1 Preparation of test pieces |
| 73 | A.6.2 Initial tensile adhesion strength A.6.3 Tensile adhesion strength after water contact A.6.4 Alternative method for tensile adhesion strength after water contact |
| 74 | A.6.5 Tensile adhesion strength after heat ageing A.6.6 Tensile adhesion strength after freeze–thaw cycle A.6.7 Tensile adhesion strength after contact with chlorinated water |
| 75 | A.6.8 Alternative method for tensile adhesion strength after contact with chlorinated water A.6.9 Tensile adhesion strength after contact with lime water |
| 76 | A.6.10 Evaluation and expression of the results A.7 Water impermeability |
| 78 | A.8 Crack bridging ability A.8.1 General |
| 79 | A.8.2 Crack bridging ability under standard conditions A.8.3 Crack bridging ability at low temperature A.9 Test report |
| 81 | Annex ZA (informative)Relationship of this European Standard with Regulation (EU) No.305/2011 |
Related products
-
BS EN 14891:2017
Liquid applied water impermeable products for use beneath ceramic tiling bonded with adhesives. Requirements, test…
