BS EN 15436-2:2015
$167.15
Road service area maintenance equipment – Performance assessment
| Published By | Publication Date | Number of Pages |
| BSI | 2015 | 42 |
This European Standard specifies the accuracy of the performance measurement system of road service area maintenance equipment described in the scope of CEN/TC 337 and used for:
-
grass-cutting and brush-cutting;
-
mechanical plant-cutting.
This equipment is mounted on self-propelled carrying vehicles and is designed to cut and shred grass, brushwood, trees, saplings and bushes in road service areas.
This European Standard does not cover the collection and transportation of shredded grass.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 6 | Foreword |
| 7 | Introduction |
| 8 | 1 Scope 2 Normative references 3 Terms and definitions 4 Cutting specifications check 4.1 Articulated-arm grass cutter – brushcutter 4.1.1 Cutting width (w) 4.1.2 Cutting height (h) 4.1.3 Cutting rotor stop time |
| 9 | 4.2 In-line flail mower 4.2.1 Cutting width (w) 4.2.2 Cutting height (h) 4.2.3 Cutting tool stop time 4.3 Mechanical plant cutting 4.3.1 Cutting width (w) |
| 10 | Figure 1 — Cutting width (w) 4.3.2 Cutting tool stop time 5 Kinematic properties check 5.1 General |
| 11 | 5.2 Articulated-arm grass cutters – brushcutters 5.2.1 General Figure 2 — Kinematic properties |
| 12 | 5.2.2 Horizontal range (A) 5.2.3 Embankment range (E) 5.2.4 Ditch range (D1) 5.2.5 Ditch range with slide rail (D2) 5.2.5.1 General |
| 13 | 5.2.5.2 Method of measurement Figure 3 — Method of measurement when Zp ≤ 0,9 m Figure 4 — Method of measurement when Zp ≤ 0,9 m |
| 14 | Figure 5 — Method of measurement when Zp > 0,9 m |
| 15 | 5.2.6 Offset (S) 5.2.7 Cutting head clearance angle 5.2.8 Cutting head rotation angle 5.3 In-line flail mower 5.3.1 General |
| 16 | Figure 6 — In-line flail mower 5.3.2 Horizontal range (A) 5.3.3 Horizontal clearance (Dh) 5.3.4 Embankment range (R = E + F) |
| 17 | 5.3.5 Ditch range (D = E + F) 5.3.6 Cutting head clearance angle 5.4 Mechanical plant cutting 5.4.1 General |
| 18 | Figure 7 — Mechanical plant cutting 5.4.2 Vertical range (B) 5.4.3 Hedge side range (I) |
| 19 | 5.4.4 Hedge side position variation (Δ I) 5.4.5 Maximum hedge topping height (C) 5.4.6 Offset (Dp) Figure 8 — Offset (Dp) |
| 20 | 5.4.7 Cutting head clearance angle 6 Weights and dimensions check 6.1 General Figure 9 — Rear view, rear-mounted machine |
| 21 | Figure 10 — Profile view, rear-mounted machine Figure 11 — Profile view, mid-mounted machines |
| 22 | Figure 12 — Profile view, front-mounted machines 6.2 Transport dimensions 6.2.1 General 6.2.2 Height (H) 6.2.3 Width (L1 + L2) 6.2.4 Length (Lg1 + Lg2) 6.3 Total machine weight |
| 23 | 7 Specifications check for machines driven over PTO shaft with mechanical or hydraulic power transmission 7.1 General 7.2 Measurements to be performed and data required 7.2.1 Hydraulic circuit oil temperature 7.2.2 Machine power supply 7.2.3 Cutting tool rotational speed 7.2.4 Cutting tool rotating torque |
| 24 | 7.2.5 Cutting tool circumferential speed 7.2.6 Cutting head kinetic energy 7.3 Determination of power 7.3.1 General 7.3.2 Parameters to be measured |
| 25 | 7.3.3 Formula to be applied 7.4 Performance characteristics 7.4.1 General 7.4.2 Maximum continuous power |
| 26 | 7.4.3 Maximum instantaneous power |
| 27 | 8 Specifications check for machines with power supplied by the carrying vehicle hydraulics 8.1 General 8.2 Measurements to be performed and data required 8.2.1 Hydraulic circuit oil temperature 8.2.2 Machine power supply 8.2.3 Cutting tool rotational speed 8.2.4 Cutting tool rotating torque |
| 28 | 8.2.5 Cutting tool circumferential speed 8.2.6 Cutting tool kinetic energy 8.3 Determination of power 8.3.1 General 8.3.2 Parameters to be measured |
| 29 | 8.3.3 Formula to be applied 8.4 Performance characteristics 8.4.1 General 8.4.2 Maximum continuous power |
| 30 | 8.4.3 Maximum instantaneous power |
| 31 | Annex A (informative) Presentation of results – Articulated-arm grass cutters – Brush cutters |
| 32 | Figure A.1 — Representation of kinematic properties |
| 34 | Annex B (informative) Presentation of results – In-line flail mowers |
| 36 | Annex C (informative) Presentation of results – Mechanical plant cutting |
| 37 | Figure C.1 — Representation of kinematic properties |
| 39 | Annex D (normative) Tests with movable arms Figure D.1 |
| 40 | Bibliography |
