BS EN 60317-0-7:2017
$142.49
Specifications for particular types of winding wires – General requirements. Fully insulated (FIW) zero-defect enamelled round copper wire
| Published By | Publication Date | Number of Pages |
| BSI | 2017 | 30 |
This part of IEC 60317 establishes general requirements for fully insulated (FIW) zero-defect enamelled round copper wires.
The nominal conductor diameter range is given in the relevant technical specification.
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 2 | National foreword |
| 7 | English CONTENTS |
| 9 | FOREWORD |
| 11 | INTRODUCTION |
| 12 | 1 Scope 2 Normative references 3 Terms, definitions, general notes and appearance 3.1 Terms and definitions |
| 14 | 3.2 General notes 3.2.1 Methods of test 3.2.2 Winding wire 3.3 Appearance 4 Dimensions 4.1 Conductor diameter |
| 15 | 4.2 Out of roundness of conductor (for nominal diameters over 0,090 mm up to 0,900 mm) 4.3 Minimum overall diameter 4.4 Maximum overall diameter Tables Table 1 – Dimensions of enamelled wires (R 20) |
| 16 | 5 Electrical resistance 6 Elongation 7 Springiness Table 2 – Elongation at break |
| 17 | 8 Flexibility and adherence 8.1 Mandrel winding test (for nominal conductor diameters over 0,090 mm up to 0,900 mm) Table 3 – Springiness |
| 18 | 8.2 Jerk test (for nominal diameters up to 0,900 mm) 9 Heat shock Table 4 – Mandrel diameters for mandrel winding test |
| 19 | 10 Cut through 11 Resistance to abrasion 12 Resistance to solvents 13 Breakdown voltage Table 5 – Heat shock |
| 20 | 14 Continuity of insulation (nominal conductor diameters over 0,090 mm up to 0,900 mm) 14.1 Off-line high voltage continuity 14.2 In-line high voltage continuity 15 Temperature index 16 Resistance to refrigerants 17 Solderability 18 Heat or solvent bonding Table 6 – Breakdown voltage |
| 21 | 19 Dielectric dissipation factor 20 Resistance to transformer oil 21 Loss of mass 23 Pin-hole test 30 Packaging |
| 22 | Annex A (normative) Supplemental requirements for FIW A.1 Dimensions Table A.1 – Dimensions of enamelled wires for grades FIW 3, 5, 7 and 9 |
| 23 | A.2 Electrical resistance Table A.2 – Dimensions of enamelled wires up to and including 0,090 mm and over 0,900 mm (R 20) for grades FIW 4, 6 and 8 |
| 24 | A.3 Elongation Table A.3 – Electrical resistance Table A.4 – Elongation at break |
| 25 | A.4 Springiness Table A.5 – Springiness for grades FIW 3, 5, 7 and 9 |
| 26 | A.5 Mandrel winding test Table A.6 – Springiness for grades FIW 4, 6 and 8 Table A.7 – Mandrel diameters for mandrel winding test for grade FIW 3, 5, 7 and 9 |
| 27 | A.6 Heat shock Table A.8 – Mandrel diameters for mandrel winding test for grade FIW 4, 6 and 8, nominal conductor diameters up to and including 0,090 mm and over 0,900 mm |
| 28 | Table A.9 – Heat shock for grades FIW 3, 5, 7 and 9 Table A.10 – Heat shock for grades FIW 4, 6 and 8 |
| 29 | A.7 Breakdown voltage Table A.11 – Breakdown voltage |
