BS EN 755-1:2016 – TC:2020 Edition
$186.33
Tracked Changes. Aluminium and aluminium alloys. Extruded rod/bar, tube and profiles – Technical conditions for inspection and delivery
| Published By | Publication Date | Number of Pages |
| BSI | 2020 | 49 |
This European Standard specifies the technical conditions for inspection and delivery of wrought aluminium and aluminium alloy extruded rod/bar, tube and profile for general engineering applications. This European Standard does not apply to: – forging stock (EN 603 (all parts)), – extruded precision profiles in alloys EN AW-6060 and EN AW-6063 (EN 12020 (all parts)), – products delivered in coils (EN 13957), – coiled tubes cut to length (EN 13957).
PDF Catalog
| PDF Pages | PDF Title |
|---|---|
| 29 | Contents Page |
| 31 | European foreword |
| 32 | 1 Scope 2 Normative references |
| 33 | 3 Terms and definitions 4 Ordering information |
| 35 | 5 Requirements 5.1 Production and manufacturing processes 5.2 Quality control 5.3 Chemical composition limits 5.4 Mechanical properties |
| 36 | 5.5 Freedom from surface defects 5.6 Tolerances on dimensions and form 5.7 Stress corrosion cracking resistance 5.8 Additional requirements 6 Test procedures 6.1 Sampling 6.1.1 Samples for chemical analysis |
| 37 | 6.1.2 Specimens for mechanical testing 6.1.2.1 Location and size 6.1.2.2 Orientation 6.1.2.3 Identification 6.1.2.4 Preparation 6.1.2.5 Number |
| 38 | 6.1.3 Test pieces for tensile test 6.1.3.1 Identification 6.1.3.2 Machining 6.1.3.3 Number, type and location of test pieces 6.2 Test methods 6.2.1 Chemical composition limits 6.2.2 Tensile testing 6.2.3 Brinell hardness testing 6.2.4 Measurement of dimensions |
| 39 | 6.2.5 Surface finish 6.2.6 Resistance to stress corrosion cracking 6.2.7 Additional tests 6.3 Re-tests 6.3.1 Chemical composition limits 6.3.2 Mechanical properties |
| 40 | 6.3.3 Other properties 7 Inspection documents 8 Marking of products 9 Packaging 10 Arbitration |
| 41 | Annex A (normative) Location of test pieces A.1 Round, square and hexagonal bar A.1.1 For diameter (D) or width across flats (S) up to and including 40 mm Figure A.1 — Round, square and hexagonal bar A.1.2 For diameter (D) or width across flats (S) over 40 mm Figure A.2 — Round, square and hexagonal bar |
| 42 | A.2 Rectangular bar A.2.1 For thickness up to and including 12,5 mm A.2.2 For thickness (T) over 12,5 mm and up to and including 40 mm Figure A.3 — Rectangular bar A.2.3 For thickness (T) exceeding 40 mm Figure A.4 — Rectangular bar |
| 43 | A.3 Tube Table A.1 — Test pieces for tubes A.4 Profiles A.4.1 For thickness up to and including 12,5 mm A.4.2 For thickness over 12,5 mm and up to and including 40 mm Figure A.5 — Profile |
| 44 | A.4.3 For thickness exceeding 40 mm Figure A.6 — Profile |
| 45 | Annex B (normative) Resistance to stress-corrosion cracking for alloy EN AW-7075 in tempers T73, T73510 and T73511 – Electrical conductivity Table B.1 — Lot acceptance criteria on tempers T73, T73510 and T73511 for alloy EN AW-7075 |
| 46 | Bibliography |
