Shopping Cart

No products in the cart.

IEEE C57.12.24-2016(Redline)

$51.46

IEEE Standard for Submersible, Three-Phase Transformers, 3750 kVA and Smaller: High Voltage, 34 500 GrdY/19 920 Volts and Below; Low Voltage, 600 Volts and Below (Redline)

Published By Publication Date Number of Pages
IEEE 2016
Guaranteed Safe Checkout
Category:

If you have any questions, feel free to reach out to our online customer service team by clicking on the bottom right corner. We’re here to assist you 24/7.
Email:[email protected]

Revision Standard – Active. Certain electrical, dimensional, and mechanical characteristics are covered in this standard. It also takes into consideration certain safety features of three-phase, 60 Hz, liquid-immersed, self-cooled, submersible transformers with separable insulated high-voltage connectors. These transformers are rated 3750 kVA and smaller with high voltages of 34 500 GrdY/19 920 V and below and with low voltages of 600 V and below.

PDF Catalog

PDF Pages PDF Title
1 IEEE Std C57.12.24-2016 Front Cover
2 Title page
4 Important Notices and Disclaimers Concerning IEEE Standards Documents
7 Participants
9 Introduction
10 Contents
11 1. Overview
1.1 Scope
1.2 Purpose
2. Normative references
12 3. Definitions
4. Service conditions
4.1 Cooling air temperature limit
4.2 Submerged operation
13 5. Rating data
5.1 Cooling class
5.2 Kilovolt-ampere ratings
5.3 Voltage ratings
5.4 Insulation levels
14 5.5 Impedance voltage
5.5.1 General
5.5.2 Tolerance on impedance voltage
6. Tests
6.1 General
15 6.2 Reference temperature
7. Construction
7.1 General
18 7.2 Connectors and terminals
7.2.1 High-voltage connectors
19 7.2.2 Low-voltage terminals
21 7.2.3 Neutral terminal connections
7.3 Accessories
7.3.1 Tap changer
22 7.3.2 Pressure relief
7.3.2.1 Manual pressure relief
7.3.2.2 Automatic pressure relief
7.3.3 Loadbreak switch
7.3.3.1 Loadbreak switch labeling
23 7.3.3.2 Loadbreak switch location
7.3.3.3 Loadbreak switch rotation
7.3.3.4 Loadbreak switch current-carrying capabilities
7.3.3.5 Loadbreak switch material
7.3.4 Overcurrent protection
7.3.4.1 Full range, current-limiting fuses
7.3.4.2 Bayonet fuses
24 7.3.5 Protective covers
7.4 Nameplate
7.5 Tank
7.5.1 Material requirements
7.5.1.1 Transformers located in a wet vault or manhole
25 7.5.1.2 Transformers located in a vault or manhole with cycling conditions
7.5.1.3 Material thickness
7.5.2 Tank integrity
7.5.3 Hardware
7.5.4 Other materials
7.5.5 Cover
26 7.5.6 Hand holes
7.5.7 Base
7.5.8 Lifting provisions
7.5.9 Grounding provisions
7.5.10 Finish
27 7.5.11 Insulating liquid level marking
7.5.12 Connector and terminal markings
7.6 Components for primary cable system
7.7 Angular displacement
7.8 Audible sound levels
28 8. Storage and installation
8.1 Storage
8.2 Installation
29 Annex A (informative) Use of pressure relief means
30 Annex B (informative) Bibliography
31 Back cover
IEEE C57.12.24-2016
$51.46