{"id":81917,"date":"2024-10-17T18:59:57","date_gmt":"2024-10-17T18:59:57","guid":{"rendered":"https:\/\/pdfstandards.shop\/product\/uncategorized\/ieee-269-1993\/"},"modified":"2024-10-24T19:48:29","modified_gmt":"2024-10-24T19:48:29","slug":"ieee-269-1993","status":"publish","type":"product","link":"https:\/\/pdfstandards.shop\/product\/publishers\/ieee\/ieee-269-1993\/","title":{"rendered":"IEEE 269 1993"},"content":{"rendered":"
Revision Standard – Inactive – Superseded. Superseded by IEEE Std 269-2002. Practical methods for measuring the transmission characteristics of both digital and conventional to wire analog telephone sets by means of objective measurements on a test connection are described. The test results thus obtained may be used as a means of evaluating or specifying the transmission performance of a telephone set on a standardized basis. The measurements are applicable to telephone sets incorporating carbon or linear transmitters. Measurements are over the frequency range most useful for speech: 100-5000 Hz. The test methods are not intended to be applicable to special devices, such as noise-exclusion transmitters, distant-talking transmitters, insert-type receivers, or noise-exclusion receivers equipped with large ear pads. You will receive an email from Customer Service with the URL needed to access this publication online.<\/p>\n
PDF Pages<\/th>\n | PDF Title<\/th>\n<\/tr>\n | ||||||
---|---|---|---|---|---|---|---|
1<\/td>\n | Title page <\/td>\n<\/tr>\n | ||||||
3<\/td>\n | Foreword Participants <\/td>\n<\/tr>\n | ||||||
5<\/td>\n | CONTENTS <\/td>\n<\/tr>\n | ||||||
7<\/td>\n | 1. Introduction 2. Scope <\/td>\n<\/tr>\n | ||||||
8<\/td>\n | 3. Definitions <\/td>\n<\/tr>\n | ||||||
10<\/td>\n | 4. References <\/td>\n<\/tr>\n | ||||||
11<\/td>\n | 5. Test Equipment <\/td>\n<\/tr>\n | ||||||
16<\/td>\n | 6. Test Procedure for Analog Sets 6.1 General <\/td>\n<\/tr>\n | ||||||
19<\/td>\n | 6.2 Standard Circuits 6.3 Transmit <\/td>\n<\/tr>\n | ||||||
23<\/td>\n | 6.4 Receive <\/td>\n<\/tr>\n | ||||||
27<\/td>\n | 6.5 Sidetone <\/td>\n<\/tr>\n | ||||||
28<\/td>\n | 6.6 Overall Transmission <\/td>\n<\/tr>\n | ||||||
29<\/td>\n | 6.7 Telephone Set Impedance 6.8 Telephone Set Resistance <\/td>\n<\/tr>\n | ||||||
30<\/td>\n | 7. Test Procedures for Digital Sets 7.1 General 7.2 Standard Circuits 7.3 Transmit Frequency Response 7.4 Receive Frequency Response 7.5 Sidetone Frequency Response 7.6 Overall Frequency Response 7.7 Signal-to-Distortion Ratio <\/td>\n<\/tr>\n | ||||||
33<\/td>\n | 7.8 Input-Output Linearity 7.9 Noise 7.10 Acoustic Echo Path Loss 7.11 Peak Acoustic Pressure (Steady-State Input) <\/td>\n<\/tr>\n | ||||||
35<\/td>\n | Appendix A\u2014 Distortion Using Continuous Spectrum Methods <\/td>\n<\/tr>\n | ||||||
36<\/td>\n | Appendix B\u2014Delay <\/td>\n<\/tr>\n | ||||||
38<\/td>\n | Appendix C\u2014Carbon Transmitter Orientation for Measurements in the AEN Position <\/td>\n<\/tr>\n<\/table>\n","protected":false},"excerpt":{"rendered":" IEEE Standard Methods for Measuring Transmission Performance of Analog and Digital Telephone Sets<\/b><\/p>\n |